In a High Availability configuration, a fully redundant secondary GitHub Enterprise appliance is kept in sync with the primary appliance through replication of all major datastores.
When you configure High Availability, there is an automated setup of one-way, asynchronous replication of all datastores (Git repositories, MySQL, Redis, and Elasticsearch) from the primary to the replica appliance.
GitHub Enterprise supports an active/passive configuration, where the replica appliance runs as a standby with database services running in replication mode but application services stopped.
Targeted failure scenarios
Use a High Availability configuration for protection against:
- Software crashes, either due to operating system failure or unrecoverable applications.
- Hardware failures, including storage hardware, CPU, RAM, network interfaces, etc.
- Virtualization host system failures, including unplanned and scheduled maintenance events on AWS.
- Logically or physically severed network, if the failover appliance is on a separate network not impacted by the failure.
A High Availability configuration is not a good solution for:
- Scaling-out, including geo-distributed Git read mirrors. Serving application or Git requests from a replica appliance is not yet supported.
- Backing up your primary appliance. A High Availability replica does not replace off-site backups in your disaster recovery plan. Some forms of data corruption or loss may be replicated immediately from the primary to the replica. To ensure safe rollback to a stable past state, you must perform regular backups with historical snapshots.
- Zero downtime upgrades. To prevent data loss and split-brain situations in controlled promotion scenarios, place the primary appliance in maintenance mode and wait for all writes to complete before promoting the replica.
Network traffic failover strategies
During failover, you must separately configure and manage redirecting network traffic from the primary to the replica.
DNS failover
With DNS failover, use short TTL values in the DNS records that point to the primary GitHub Enterprise appliance. We recommend a TTL between 60 seconds and five minutes.
During failover, you must place the primary into maintenance mode and redirect its DNS records to the replica appliance's IP address. The time needed to redirect traffic from primary to replica will depend on the TTL configuration and time required to update the DNS records.
Utilities for replication management
To manage replication on GitHub Enterprise, use these command line utilities by connecting to the replica appliance using SSH.
ghe-repl-setup
The ghe-repl-setup command puts a GitHub Enterprise appliance in replica standby mode.
- An encrypted OpenVPN tunnel is configured for communication between the two appliances.
- Database services are configured for replication and started.
- Application services are disabled. Attempts to access the replica appliance over HTTP, Git, or other supported protocols will result in an "instance in replica mode" maintenance page or error message.
For example:
admin@169-254-1-2:~$ ghe-repl-setup 169.254.1.1 Verifying ssh connectivity with 169.254.1.1 ... Connection check succeeded. Configuring database replication against primary ... Success: Replica mode is configured against 169.254.1.1. To disable replica mode and undo these changes, run `ghe-repl-teardown'. Run `ghe-repl-start' to start replicating against the newly configured primary.
ghe-repl-start
The ghe-repl-start command turns on active replication of all datastores:
admin@169-254-1-2:~$ ghe-repl-start Starting OpenVPN tunnel ... Starting MySQL replication ... Starting Redis replication ... Starting Elasticsearch replication ... Starting Pages replication ... Starting Git replication ... Success: replication is running for all services. Use `ghe-repl-status' to monitor replication health and progress.
ghe-repl-status
The ghe-repl-status command returns an OK, WARNING or CRITICAL status for each datastore replication stream. When any of the replication channels are in a WARNING state, the command will exit with the code 1. Similarly, when any of the channels are in a CRITICAL state, the command will exit with the code 2.
admin@169-254-1-2:~$ ghe-repl-status OK: mysql replication in sync OK: redis replication is in sync OK: elasticsearch cluster is in sync OK: git data is in sync (10 repos, 2 wikis, 5 gists) OK: pages data is in sync
The -v and -vv options give details about each datastore's replication state:
ghe-repl-status -v
OK: mysql replication in sync
| IO running: Yes, SQL running: Yes, Delay: 0
OK: redis replication is in sync
| master_host:169.254.1.1
| master_port:6379
| master_link_status:up
| master_last_io_seconds_ago:3
| master_sync_in_progress:0
OK: elasticsearch cluster is in sync
| {
| "cluster_name" : "github-enterprise",
| "status" : "green",
| "timed_out" : false,
| "number_of_nodes" : 2,
| "number_of_data_nodes" : 2,
| "active_primary_shards" : 12,
| "active_shards" : 24,
| "relocating_shards" : 0,
| "initializing_shards" : 0,
| "unassigned_shards" : 0
| }
OK: git data is in sync (366 repos, 31 wikis, 851 gists)
| TOTAL OK FAULT PENDING DELAY
| repositories 366 366 0 0 0.0
| wikis 31 31 0 0 0.0
| gists 851 851 0 0 0.0
| total 1248 1248 0 0 0.0
OK: pages data is in sync
| Pages are in sync
ghe-repl-stop
The ghe-repl-stop command temporarily disables replication for all datastores and stops the replication services. To resume replication, use the ghe-repl-start command.
admin@168-254-1-2:~$ ghe-repl-stop Stopping Pages replication ... Stopping Git replication ... Stopping MySQL replication ... Stopping Redis replication ... Stopping Elasticsearch replication ... Stopping OpenVPN tunnel ... Success: replication was stopped for all services.
ghe-repl-promote
The ghe-repl-promote command disables replication and converts the replica appliance to a primary. The appliance is configured with the same settings as the original primary and all services are enabled.
admin@168-254-1-2:~$ ghe-repl-promote Enabling maintenance mode on the primary to prevent writes ... Stopping replication ... | Stopping Pages replication ... | Stopping Git replication ... | Stopping MySQL replication ... | Stopping Redis replication ... | Stopping Elasticsearch replication ... | Stopping OpenVPN tunnel ... | Success: replication was stopped for all services. Switching out of replica mode ... | Success: Replication configuration has been removed. | Run `ghe-repl-setup' to re-enable replica mode. Applying configuration and starting services ... Success: Replica has been promoted to primary and is now accepting requests.
ghe-repl-teardown
The ghe-repl-teardown command disables replication mode completely, removing the replica configuration.
